Maintaining the proper function of your equipment is essential for the smooth operation of your food service business. At FWEParts, we understand the importance of ensuring your units are in top condition. This guide, “How to Perform Door and Latch Adjustments on FWE Units,” provides step-by-step instructions to help you keep your doors and latches operating perfectly. With clear and concise steps, you’ll be able to address issues such as improper door closure and latch malfunction, ensuring your equipment performs reliably. For any additional assistance or inquiries, our dedicated support team is always available. Contact us at 1-615-805-3270 or service@hatcodirect.com for expert guidance.

Tools Needed

• Driver Drill with #2 Phillips Bit
• Flat Blade Screwdriver
• Level

Steps

Door Adjustment (If the door is not closing properly)

0:21 | Step 1: Locate and remove hinge covers from the door hinges.

0:33 | Step 2: Loosen all screws that mount the hinges to both the door and the unit.

0:43 | Step 3: Carefully adjust the door in and out, and side to side taking note of the door leveling and any gaps.

0:51 | Step 4: With the door in a level position, retighten the screws loosened in Step 2.

0:59 | Step 5: Test the door for proper sealing and closure. Re[peat steps 2 – 4 as needed.

1:05 | Step 6: Once the door seals properly and is level, reinstall the hinge covers and return the unit to service.

Latch Adjustment (if the door is not latching properly)

1:16 | Step 1: Locate the door latch and screw for the J-Hook on the bottom side of the latch. Loosen the screw.

1:27 | Step 2: Carefully adjust the J-Hook in and out, tightening the screw and then testing the closure of the unit.

1:33 | Step 3: Repeat Steps 1 & 2 as needed.

1:40 | Step 4 Once the floor handle properly locks onto the latch, confirm the J-Hook is sufficiently high and in place. Test the door for proper sealing and return the unit to service.

As we conclude this guide on performing door and latch adjustments on FWE units, we hope the instructions have been clear and helpful. At FWEParts, our priority is to ensure your equipment operates flawlessly, supporting the efficiency and success of your food service business. If you require further guidance on these adjustments or have any other questions, our expert team is always here to assist you. Feel free to contact us at 1-615-805-3270 or service@hatcodirect.com for personalized support. We’re dedicated to your success and are just a call or an email away.

The post How to Perform Door and Latch Adjustments on FWE Units appeared first on OEM Parts for Hatco Equipment | Hatco Trade Direct Parts.

In the dynamic environment of the food service industry, the functionality of every component, including doors, plays a vital role in operational efficiency and customer satisfaction. Recognizing this, FWEParts is committed to providing easy-to-follow, practical guides for maintaining and servicing your FWE equipment. In our latest tutorial, we delve into the specifics of how to replace and perform general service to doors on FWE units. This guide is designed to empower you with the knowledge needed to ensure your equipment operates at its best. For any additional assistance or inquiries, our support team is readily available. Reach out to us at 1-615-805-3270 or send an email to service@hatcodirect.com for expert advice and guidance.

Ordering Replacement Doors and Replacement Door Parts

• If you need to order new doors for your FWE unit, please follow this link for a comprehensive selection and an easy purchasing process

Tools Needed

• Driver Drill with #2 Phillips Bit
• Flathead Screwdriver
• Small Screwdriver (Regular or Phillips)
• Needle Nose Pliers

Steps

0:00 | Introduction

Door Adjustment

0:24 | Step 1: Locate door hinges and remove the hinge covers

0:39 | Step 2: Loosen all the screws that mount the hinges to both the door and the unit.

0:46 | Step 3: Carefully adjust the door in and out and side to side, taking note of the door leveling and any gaps.

0:55 | Step 4: Retighten screws loosened in Step 2.

1:09 | Step 5: Test door for proper sealing. Repeat Steps 2 – 4 as needed.

1:16 | Step 6: Once the floor seals properly and is level, reinstall the hinge covers and return the unit to service.

Door Reversal (Hinging Swap for Standard Doors)

1:25 | Step 1: Locate the door hinges and remove the covers in the middle of the hinge.

1:42 | Step 2: Remove screws that mount the hinges to the unit.

1:55 | Step 3: Flip the door 180 degrees and reinstall the unit using the same hardware that was removed previously.

2:09 | Step 4: Test the door for proper sealing, then reinstall the hinge covers and return the unit to service. (The FWE decal can be flipped and moved to the top of the flipped door – Contact the FWE Service Department if a new decal is required.)

Door Reversal (Hinging Swap for Doors with Spring Kit)

2:19 | Step 1: Locate the door hinges and remove the covers in the middle of the hinge, exposing the spring.

2:35 | Step 2: On top of the spring, locate the keeper pin. Using a small screwdriver, relieve tension from the spring while removing the keeper pin.

2:45 | Step 3: Once the keeper pin is removed, relieve pressure from the spring.

2:52 | Step 4: Using a flat screwdriver, pry the spring out of the holder. This will expose the screws so the door can be removed from the unit.

3:02 | Step 5: Remove the screws that mount the hinges to the unit.

3:16 | Step 6: Flip the door 180 degrees and reinstall it on the unit using the same hardware previously removed.

3:28 | Step 7: Pretension the spring on the hinge using a small screwdriver inserted into the hole where the keeper pin goes.

3:36 | Step 8: Set top door spring tension by turning the collar on the spring 3 holes and inserting the keeper pin so that the tension holds it in place.

3:56 | Step 9: Set the bottom door spring tension by turning the collar on the spring 2 holes and inserting the keeper pin so that the tension holds it in place.

4:04 | Step 10: Once tensions have been set, test doors to make sure they seal properly. Return the unit to service. (The FWE decal can be flipped and moved to the top of the flipped door – Contact the FWE Service Department if a new decal is required.)

Hinge Replacement (Standard Door)

4:15 | Step 1: Locate the door hinges and remove the covers in the middle of the hinge.

4:30 | Step 2: Remove the screws mounting hinges to the unit and carefully set the door aside.

4:43 | Step 3: Remove the screws mounting the hinges to the door. Discard old hinges.

4:51 | Step 4: Using the screws removed in Step 3, install the new hinges onto the door.

4:57 | Step 5: Remount the door using screws removed in Step 2, securing the hinges to the unit.

5:07 | Step 6: Check the door for proper sealing and operationality.

5:14 | Step 7: Reinstall the hinges covers and return the unit to service.

Hinge Replacement (Doors with Spring Kit)

5:25 | Step 1: Locate the door hinges and remove the covers in the middle of the hinge, exposing the spring.

5:33 | Step 2: Locate the keeper pin on top of the spring. Using a small screwdriver, relieve tension from the spring while removing the keeper pin.

5:45 | Step 3: Once the keeper pin is removed, relieve pressure from the spring.

5:52 | Step 4: Using a flat screwdriver, pry the spring out of the holder. This will expose the screws so the door can be removed from the unit.

6:02 | Step 5: Remove the screws mounting hinges to the unit and carefully set for aside.

6:16 | Step 6: Remove the screws mounting the hinges to the door. Discard old hinges.

6:23 | Step 7: Using the screws removed in Step 6, install the new hinges onto the door.

6:30 | Step 8: Remount the door using the screws removed in Step 5, securing the hinges to the unit.

6:40 | Step 9: Reinstall the spring removed in Step 4.

6:45 | Step 10: Pretension the spring on the hinge using a small screwdriver inserted into the hole where the keeper pin goes.

6:53 | Step 11: Set the top door spring by turning the collar on the spring 3 holes and inserting the keeper pin so that the tension holds it in place.

7:12 | Step 12: Set the bottom door spring tension by turning the spring 2 holes and inserting the keeper pin so that the tension holds it in place.

7:23 | Step 13: Once tensions have been set, test to make sure they seal properly. Reinstall thing covers and return the unit to service.

As we conclude this guide on replacing and servicing doors on FWE units, we hope you have found the information both informative and easy to follow. At FWEParts, our goal is to ensure your equipment functions flawlessly, contributing to the smooth operation of your food service business. Remember, our team is always here to support you, whether it’s for further guidance on maintenance tasks or addressing any other concerns you might have. Don’t hesitate to contact us at 1-615-805-3270 or through email at service@hatcodirect.com for personalized assistance. We’re dedicated to your success and are just a call or an email away.

The post How to Replace and Perform General Service on Doors appeared first on OEM Parts for Hatco Equipment | Hatco Trade Direct Parts.

In the bustling world of the food service industry, the mobility and stability of your equipment is essential for efficient operation and service excellence. At FWEParts, we are dedicated to ensuring that every aspect of your FWE equipment functions optimally. This includes providing detailed, user-friendly guides for essential maintenance tasks. Our latest tutorial focuses on how to replace casters on FWE units, a key step in maintaining the maneuverability and safety of your equipment. With this guide, you’ll be equipped with the knowledge to perform this task swiftly and effectively. For any questions or further assistance, our expert team is always on standby. Feel free to contact us at 1-615-805-3270 or email us at service@hatcodirect.com for any help you may need.

Ordering Replacement Casters

If you are in need of new casters for your FWE unit, you can easily find and purchase them by visiting this link. Our selection ensures you get the right match for your equipment, guaranteeing quality and compatibility.

Tools Needed

• Socket Wrench with 1/2″ Socket
• Socket Extender

Steps

0:00 | Introduction

Replacing Casters (Non Refrigeration)

0:24 | Step 1: Remove all racks, tray slides, and/or shelving inside the unit. Place the unit onto its back, using a buffer such as cardboard or styrofoam to prevent scratches to the outside of the unit.

0:35 | Step 2: Using a socket wrench, remove the four nuts and washers mounting the caster to the unit. Remove and discard the caster.

0:51 | Step 3: Install new caster, making sure studs line up with the caster plate. Use nuts and washers removed in Step 2 to mount in place.

1:16 | Step 4: Place the unit upright and test for functionality.

1:25 | Step 5: Reinstall all racks, tray slides, and/or shelving inside the unit. Return to service.

Replacing Casters (Refrigeration)

1:30 | Step 1: Remove all racks, tray slides, and/or shelving inside the unit. Using a lift, raise the unit in the air for clearance tall enough for tools underneath the unit.

2:01 | Step 2: Using a socket wrench, remove the four nuts and washers mounting the caster to the unit. Remove and discard the caster.

2:17 | Step 3: Install new caster, making sure studs line up with the caster plate. Use nuts and washers removed in Step 2 to mount in place.

2:37 | Step 4: Set the unit back down and remove off the lift. Test for operationality.

2:45 | Step 5: Reinstall all racks, tray slides, and/or shelving inside the unit. Return to service.

As we wrap up this guide on replacing casters for FWE units, we trust that you have found the instructions clear and helpful. Our commitment at FWEParts is to provide you with the resources and support you need to keep your equipment running smoothly and efficiently. Remember, our team is here to assist you with any additional questions or guidance you may require in maintaining your FWE equipment. Please don’t hesitate to reach out to us at 1-615-805-3270 or via email at service@hatcodirect.com for personalized support. Your success in the food service industry is our priority, and we are always ready to help ensure your equipment performs at its best.

The post How to Replace Casters used on FWE Units appeared first on OEM Parts for Hatco Equipment | Hatco Trade Direct Parts.

The post Canned Fuel Shroud Installation appeared first on OEM Parts for Hatco Equipment | Hatco Trade Direct Parts.